MASON C-RE 585 Epoxy Chemical Anchor
MASON C-RE 585 Epoxy Chemical Anchor mortar is a 2-component reaction resin mortar based on a pure epoxy, it is characterized, by a high range of applications with an installation temperature from +5.C and a service temperature up to 72.C as well as by high chemical resistance for applications in extreme ambiences e.g. in swimming pools(chlorine) or closeness to the sea(salt).
It is approved for:
- Diamond-drilled holes
- Water-filled drill holes
- Seismic applications C1, C2
MASON C-RE (PURE EPOXY CHEMICAL ANCHOR) – INSTALLATION OF REINFORCING BARS
MASON C-RE PURE EPOXY CHEMICAL INJECTION ANCHOR – ON SITE TENSILE PULL OUT TEST
Below are some photos taken during the on-site pull out test conducted by Fasten Enterprises. This is a test typically performed to establish or check the loading of a typical fastener/ anchor with concrete or securing base materials. We provide trained personnel to perform onsite tensile pull-out tests for our clients. To ensure the accuracy of such tests, our equipment is regularly calibrated by accredited test laboratories.
- European Technical Assessment Certification
- 4 hrs CSTB Fire Resistance Tested
- HDB Material List – Singapore
- Ultimate Performance Tested by SETSCO Singapore
- KMITL Thailand Tested
- High Viscosity, Long Working Time
- Applicable in Cracked and Un-cracked Concrete
- Damp, Wet and Under Water Holes Applicable
- High bending strength 47 N/mm2 acc. to EN 196 Part 1
- High compressive strength 137 N/mm2 acc. to EN 196 Part 1
- High Chemical Resistance
- Non-Shrinkage, Low odour
- Resealable UV Resistance Hard Plastic Cartridge
- Heavy anchoring – doweling and post-installed rebar connection
- Hammer drilled and diamond drilled holes applicable
- High viscosity ; ideal for overhead application
- Suitable for attachment point close to the edge, since anchoring is free of expansion forces
- Suitable for dynamic load; Cracked concrete applicable
- Strong and secure anchoring even under water; water filled bore holes applicable
- Water-impermeable acc. to DIN EN 12390-8
- Fire resistance and high chemical resistance
- Low shrinkage: ideal for larger annular gap
- Low odour; ideal for indoor application
- Safe for use as a component in a drinking water system
- Flexible working time at elevated temperatures
- Resealable cartridge: can be reused up to the end of the shelf life
Reactivity
|
Temperature of base material |
Gelling and working time |
Full curing time in dry base material |
Full curing time in wet base material |
|
+5°C |
120 Min. |
50 hrs |
100 hrs |
|
+10°C |
90 Min. |
30 hrs |
60 hrs |
|
+20°C |
30 Min. |
10 hrs |
20 hrs |
|
+30°C |
20 Min. |
6 hrs |
12 hrs |
|
+40°C |
12 Min. |
4 hrs |
8 hrs |
Base Material
Cracked concrete, uncracked concrete, light concrete, porous concrete, solid masonry, natural stone; hammer drilled and diamond drilled holes
Anchor Elements
Threaded rods (zinc plated or hot dip galvanized, stainless steel and high corrosion resistance steel), reinforcing bars, internal threaded rods, profile rod, steel section with undercuts (e.g. perforated section)
Temperature Range
+5°C up to +40°C temperature of the base material; cartridge temperature min. +5°C; optimal +20°C; -40°C to +72°C base material temperature after full curing
Suitable Application
Suitable for facades, roofs, metal construction; metal profiles, column, beam, console, railing, sanitary devices, cable trays, piping, post-installed rebar connection (reconstruction or reinforcement),building reconstruction and renovation, etc.
